收藏本站
MCP2030 Bidirectional Communication Demo Kit User’s Guide
strength. This current output is fed into a resistor and the voltage across the resistor is
fed into the MCP3421 ADC input pin. The converted16-bit ADC output is then fed into
the MCU.
The function of the MCP2030 is controlled by its configuration register settings. Highly
intelligent signal detection and response (bidirectional communications) is possible by
utilizing the MCP2030 configuration register settings. The user can easily change or
modify the included firmware for different settings of the MCP2030 configuration
registers for their own applications.
3.3.4
UHF Transmitter (433.92 MHz)
A 433.92 MHz UHF transmitter is used to transmit the Transponder Demo Board data
to the Base Station Demo Board. The UHF transmitter is based on a surface acoustic
wave (SAW) resonator. The transmitter is turned on during the high duration of the data
and off during the low duration of the bit data.
Note:
3.3.5
The design and layout of this transmitter is not sufficient to ensure
compliance with EC or FCC regulations.
Analog-to-Digital Converter (MCP3421)
The Transponder Demo Board uses an MCP3421 ADC to convert the analog RSSI
output of the MCP2030 to digital data. The MCP3421 is a delta-sigma analog-to-digital
converter with 12, 14, 16, and 18 bit mode options. In this demo board, the converter
is configured for the 16 bit and one-shot mode. When the transponder is powered-up,
the MCU sends an I 2 C write command to the MCP3421 for one-shot mode and 16 bit
conversion. After one conversion, the device stays in a low power standby mode.
During this mode, the device draws only about 1 μA. When the MCP2030 analog
front-end device receives a valid Base Station command, then the MCU sends an I 2 C
read command to the MCP3421 ADC for the analog-to-digital data conversion. At this
moment, the Base Station Demo Board transmits a continuous LF signal for about
50 ms allowing the MCP2030 to collect the RSSI values. The RSSI voltage across the
RSSI load resistor is fed into the MCP3421 input pin. After the MCU sends the I 2 C read
command, it is waiting for the MCP3421 to complete the conversion by checking the
RDY bit of the MCP3421 output. In typical operation, it takes about 50 ms to complete
a 16 bit conversion. See Figure 2-2 and Figure 2-3 for more information on the ADC
operation.
TABLE 3-1:
PIC16F636 I/O CONNECTIONS
PORT Pin
Port A
RA0
Switch 4
Function
Notes
ICSP? Data
RA1
RA2
RA3
RA4
RA5
Port C
RC0
RC1
RC2
RC3
RC4
RC5
? 2006 Microchip Technology Inc.
Switch 3
LFDATA Input from MCP2030, SPI SDIO for MCP2030
SPI SCLK Output for MCP2030
RF Active LED
SPI CS output for MCP2030
I 2 C SDA for MCP3421
I 2 C SCL for MCP3421
Valid LFDATA Input Indicator LED
RF Data Out
ICSP Clock
ICSP MCLR
DS51637A-page 15
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MCP9502PT-095E/OT IC TEMP SWITCH PROGR P-P SOT23-5
MCP9510CT-E/CH IC TEMP SWITCH OD 125C SOT23-6
MD7IC18120NR1 IC PWR AMP RF LDMOS TO270-16
MDEV-315-HH-KF-MS KIT MASTER DEV MS KEYFOB 315MHZ
MDEV-418-HH-CP8-HS KIT DEV TX 418MHZ HS COMPACT
MDEV-418-HH-LR8-HS KIT DEV TX 418MHZ HS LONG-RANGE
MDEV-433-HH-CP8-MS KIT DEV TX 433MHZ MS SERIES
MDEV-433-HH-LR8-MS KIT DEV TX 433MHZ MS SER LONG-RG
相关代理商/技术参数
MCP2030-I/P 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel
MCP2030-I/P 制造商:Microchip Technology Inc 功能描述:Analog Front End Device IC
MCP2030-I/SL 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel
MCP2030-I/ST 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel
MCP2030T 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Three-Channel Analog Front-End Device
MCP2030T-I/P 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Three-Channel Analog Front-End Device
MCP2030T-I/SL 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel
MCP2030T-I/ST 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel